DSPIC30F4011-30I/ML【PDF 63/238 页】IC DSPIC MCU/DSP 48K 44QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1917

59页 60页 61页 62页 [63页]64页 65页 66页 67页

2010 Microchip Technology Inc.

DS70135G-page 155

dsPIC30F4011/4012

21.2.3

LP OSCILLATOR CONTROL

Enabling the LP oscillator is controlled with two

elements:

Current oscillator group bits, COSC<1:0>

LPOSCEN bit (OSCCON<1>)

The LP oscillator is on (even during Sleep mode) if

LPOSCEN = 1. The LP oscillator is the device clock if:

COSC<1:0> = 00 (LP selected as main osc.) and

LPOSCEN = 1

Keeping the LP oscillator on at all times allows for a

fast switch to the 32 kHz system clock for lower power

operation. Returning to the faster main oscillator still

requires a start-up time.

21.2.4

PHASE LOCKED LOOP (PLL)

The PLL multiplies the clock which is generated by the

primary oscillator. The PLL is selectable to have either

gains of x4, x8 or x16. Input and output frequency

ranges are summarized in Table 21-3.

TABLE 21-3:

PLL FREQUENCY RANGE

The PLL features a lock output which is asserted when

the PLL enters a phase locked state. Should the loop

fall out of lock (e.g., due to noise), the lock signal is

rescinded. The state of this signal is reflected in the

read-only LOCK bit in the OSCCON register.

21.2.5

FAST RC OSCILLATOR (FRC)

The FRC oscillator is a fast (7.37 MHz, ±2% nominal),

internal RC oscillator. This oscillator is intended to

provide reasonable device operating speeds without

the use of an external crystal, ceramic resonator or RC

network. Using the x4, x8 and x16 PLL options, higher

operational frequencies can be generated.

The dsPIC30F operates from the FRC oscillator when-

ever the Current Oscillator Selection (COSC<1:0>)

control

bits

the

OSCCON

(OSCCON<13:12>) are set to ‘01’.

There are four tuning bits (TUN<3:0>) for the FRC

oscillator in the OSCCON register. These tuning bits

allow the FRC oscillator frequency to be adjusted as

close to 7.37 MHz as possible, depending on the

device operating conditions. The FRC oscillator

frequency has been calibrated during factory testing.

Table 21-4 describes the adjustment range of the

TUN<3:0> bits.

TABLE 21-4:

FRC TUNING

21.2.6

LOW-POWER RC OSCILLATOR (LPRC)

The LPRC oscillator is a component of the Watchdog

Timer (WDT) and oscillates at a nominal frequency of

512 kHz. The LPRC oscillator is the clock source for

the Power-up Timer (PWRT) circuit, WDT and clock

monitor circuits. It may also be used to provide a low-

frequency clock source option for applications where

power consumption is critical and timing accuracy is

not required.

The LPRC oscillator is always enabled at a POR

because it is the clock source for the PWRT. After the

PWRT expires, the LPRC oscillator remains on if one

of the following is true:

The Fail-Safe Clock Monitor is enabled

The WDT is enabled

The LPRC oscillator is selected as the system

clock via the COSC<1:0> control bits in the

OSCCON register

If one of the above conditions is not true, the LPRC

shuts off after the PWRT expires.

FIN

PLL

Multiplier

FOUT

4 MHz-10 MHz

16 MHz-40 MHz

4 MHz-10 MHz

32 MHz-80 MHz

4 MHz-7.5 MHz

x16

64 MHz-120 MHz

Note:

OSCTUN functionality has been provided

help

customers

compensate

for

temperature effects on the FRC frequency

over a wide range of temperatures. The

tuning step size is an approximation and is

neither characterized nor tested.

TUN<3:0>

Bits

FRC Frequency

0111

+10.5%

0110

+9.0%

0101

+7.5%

0100

+6.0%

0011

+4.5%

0010

+3.0%

0001

+1.5%

0000

Center Frequency (oscillator is

running at calibrated frequency)

1111

-1.5%

1110

-3.0%

1101

-4.5%

1100

-6.0%

1011

-7.5%

1010

-9.0%

1001

-10.5%

1000

-12.0%

Note 1: OSC2 pin function is determined by the

Primary

Oscillator

mode

selection

(FPR<3:0>).

2: Note that OSC1 pin cannot be used as an

I/O pin, even if the secondary oscillator or

an internal clock source is selected at all

times.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式